Skip to main content

Apache Status Codes

Often when debugging a problem or looking through your logs you will see the apache status codes

For Example
xxx.xxx.xxx.xxx - - [28/Jul/2006:13:49:28 +0200] "GET /news.php HTTP/1.1" 200 807 "http://www.joe-ma.co.za/news.php" "Mozilla/5.0 (X11; U; Linux i686; en-US; rv:1.9a1) Gecko/20060703 FreeBSD/amd64 Minefield/3.0a1"





Successful Client Requests
200 OK
201 Created
202 Accepted
203 Non-Authorative Information
204 No Content
205 Reset Content
206 Partial Content

Client Request Redirected
300 Multiple Choices
301 Moved Permanently
302 Moved Temporarily
303 See Other
304 Not Modified
305 Use Proxy

Client Request Errors
400 Bad Request
401 Authorization Required
402 Payment Required (not used yet)
403 Forbidden
404 Not Found
405 Method Not Allowed
406 Not Acceptable (encoding)
407 Proxy Authentication Required
408 Request Timed Out
409 Conflicting Request
410 Gone
411 Content Length Required
412 Precondition Failed
413 Request Entity Too Long
414 Request URI Too Long
415 Unsupported Media Type

Server Errors
500 Internal Server Error
501 Not Implemented
502 Bad Gateway
503 Service Unavailable
504 Gateway Timeout
505 HTTP Version Not Supported
Labels:

Comments

Post a Comment

Popular posts from this blog

Setting up and Installing Rancid on FreeBSD for Cisco Products

Setting up and Installing Rancid on FreeBSD for Cisco Products What is Rancid? Rancid is an application that monitors a devices configuration including software and hardware. The configuration is then stored in a Concurrent Version System or CVS. Most of the time it is used to back up router, switch and firewall configurations, as well as notify you when a configuration has changed, i.e a firewall rule or a routers IP address or access list change. here is an example of the output =================================================================== retrieving revision 1.29 diff -u -4 -r1.29 mpls-jhb-pe1 @@ -288,9 +288,9 @@ ! interface Serial0/0 description Link to Client X bandwidth 2048 - ip address 192.168.1.244 255.255.255.254 + ip address 192.168.1.234 255.255.255.254 ip route-cache flow ip tcp header-compression iphc-format ip tcp compression-connections 256 ! ip ospf message-digest-key 1 md5 the - symbol represents what was removed the + symbol represents what was added The abo...
2 comments
Read more

Tacacs+ Install and Config Guide

Tacacs+ Install and Config Guide What is TACACS As per wikipedia Terminal access controller access control system (TACACS) is a remote authentication protocol that is used to communicate with an authentication server commonly used in UNIX networks. TACACS allows a remote access server to communicate with an authentication server in order to determine if the user has access to the network. Installing Tacacs on FreeBSD This guide is intended to be a basic implementation of TACACS+, so although there are may features I am just going to document what I generally use. Please note that tac_plus is also available from Shrubbery Networks if you would like to install and configure on another platform. You may also want to check out my Rancid How-To Once again its in your ports directory. cd to /usr/ports/net/tac_plus4/ run a "make install clean" Once installed vi /usr/local/etc/rc.d/tac_plus.sh Then Change the following line from NO to YES tac_plus_enable=$ Save the file, then vi /e...
Post a Comment
Read more

Configuring FreeBSD Postfix Mailscanner and Mailwatch

Configuring Mailscanner Mailwatch and Postfix for FreeBSD The Install guide is here I have split the install guide and the configuration guide as they are pretty involved and might cause confusion if they where put together. I will start off with the easier stuff like clamav and then move on to spamassassin and postfix and then finally to mailscanner and mailwatch. if you have not already read the Install Guide Which might be helpful to newcomers here is a summery of what has been installed. Apache and php - this is for the Mailwatch web frontend. Mysql - This is where mailscanner will log info and where your black and white lists will live. Mailwatch - Mailwatch is the web front end to help monitor and manage Mailscanner. Spamassassin - This is the system that checks the mail content looking for spam. Clamav - the Antivirus scanner that Mailscaner will use Mailscanner - The server that uses all of the above to keep your mail clean and spam free. Ok now that that is over: Confi...
2 comments
Read more