Skip to main content

Welcome to the new home of www.joe-ma.co.za

Hi all
I have moved all the content over to blogspot. in the hopes of adding more features and getting the access speed up.
All the articles are here including the most popular ones like Cisco DynDNS config and Cisco Static DHCP.

ALL of them are waiting for you folks to go check out.
I hope these How-Tos are going to help you.
Please check on the "Blog Archive" on the left side of the screen for all the articles, or check the Right side for the Labels. In the Label box you will see the tags like Cisco Dynamic DNS Rancid Tacacs+ FreeBSD etc.

I will be moving the www.joe-ma.co.za domain over to blogspot in the next 2 months or so.

Comments

Post a Comment

Popular posts from this blog

Setting up and Installing Rancid on FreeBSD for Cisco Products

Setting up and Installing Rancid on FreeBSD for Cisco Products What is Rancid? Rancid is an application that monitors a devices configuration including software and hardware. The configuration is then stored in a Concurrent Version System or CVS. Most of the time it is used to back up router, switch and firewall configurations, as well as notify you when a configuration has changed, i.e a firewall rule or a routers IP address or access list change. here is an example of the output =================================================================== retrieving revision 1.29 diff -u -4 -r1.29 mpls-jhb-pe1 @@ -288,9 +288,9 @@ ! interface Serial0/0 description Link to Client X bandwidth 2048 - ip address 192.168.1.244 255.255.255.254 + ip address 192.168.1.234 255.255.255.254 ip route-cache flow ip tcp header-compression iphc-format ip tcp compression-connections 256 ! ip ospf message-digest-key 1 md5 the - symbol represents what was removed the + symbol represents what was added The abo...
2 comments
Read more

Tacacs+ Install and Config Guide

Tacacs+ Install and Config Guide What is TACACS As per wikipedia Terminal access controller access control system (TACACS) is a remote authentication protocol that is used to communicate with an authentication server commonly used in UNIX networks. TACACS allows a remote access server to communicate with an authentication server in order to determine if the user has access to the network. Installing Tacacs on FreeBSD This guide is intended to be a basic implementation of TACACS+, so although there are may features I am just going to document what I generally use. Please note that tac_plus is also available from Shrubbery Networks if you would like to install and configure on another platform. You may also want to check out my Rancid How-To Once again its in your ports directory. cd to /usr/ports/net/tac_plus4/ run a "make install clean" Once installed vi /usr/local/etc/rc.d/tac_plus.sh Then Change the following line from NO to YES tac_plus_enable=$ Save the file, then vi /e...
Post a Comment
Read more

FreeBSD, Postfix, Mailscanner and Mailwatch Installation

Installing postfix, mailscanner and mailwatch on FreeBSD I have setup a number of servers using mailscanner and postfix to do antispam and antivirus checking. This particular example will show you how to set the server up as a mail gateway. i.e. all inbound and outbound mail will go via this server. You can also use the server as a pop3/imap4 server and doing so, does make life a little easier as you don't have to worry about the transport and relay_hosts files. At a later stage I will show that info too..... when I get a chance. This my seem strange but as there is quite a bit involved in installing and configuring I am splitting this into two How-To's this one, The install How-To and the configuration How-To First off its probably best to start on a new install of FreeBSD. Once you have done the initial portsnap fetch and portsnap extract Right here we go. Two things you might want to do is force your NIC to 100MB full duplex and install lsof Type in ifconfig and check if the...
1 comment
Read more